ARUBA IAP-225 APIN0225 INSTANT ACCESS POINT 5GHz 2.4GHz brand new
ARUBA IAP-225 APIN0225 INSTANT ACCESS POINT 5GHz 2.4GHz brand new, never use, in original box (open box).
AC-DC 12vdc power unit is NOT included (you can use PoE instead)
For Spec detail please see this link https://www.arubanetworks.com/assets/ds/DS_AP220Series.pdf
AP-220 SERIES SPECIFICATIONS • AP-225 and IAP-225 - 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3x3 MIMO and three integrated omnidirectional downtilt antennas. • AP-224 and IAP-224 - 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3x3 MIMO and three combined, diplexed external antenna connectors. WIRELESS RADIO SPECIFICATIONS • AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11n - In addition to 802.11n data rates, the 2.4-GHz radio supports 802.11ac data rates using 256-QAM modulation. This gives TurboQAM-enabled clients a 33% boost above the maximum supported data rate. • Software-configurable dual radio supports 5 GHz and 2.4 GHz • 3x3 MIMO with three spatial streams and up to 1.3 Gbps wireless data rate • Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio • Supported frequency bands (country-specific restrictions apply): - 2.4000 GHz to 2.4835 GHz - 5.150 GHz to 5.250 GHz - 5.250 GHz to 5.350 GHz - 5.470 GHz to 5.725 GHz - 5.725 GHz to 5.850 GHz • Available channels: Dependent upon configured regulatory domain • Dynamic frequency selection (DFS) optimizes the use of available RF spectrum • Supported radio technologies: - 802.11b: Direct-sequence spread-spectrum (DSSS) - 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) - 802.11n/ac: 3x3 MIMO with up to three spatial streams • Supported modulation types: - 802.11b: BPSK, QPSK, CCK - 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM - 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM • Transmit power: Configurable in increments of 0.5 dBm • Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements): - 2.4-GHz band: +23 dBm (18 dBm per chain) - 5-GHz bands: +23 dBm (18 dBm per chain) • Advanced cellular coexistence (ACC) feature to effectively deal with interference from cellular systems • Maximum ratio combining (MRC) for improved receiver performance • Cyclic delay diversity (CDD) for improved downlink RF performance • Short guard interval for 20-MHz, 40-MHz and 80-MHz channels • Space-time block coding (STBC) for increased range and improved reception • Low-density parity check (LDPC) for high-efficiency error correction and increased throughput • Transmit beam-forming (TxBF) for increased reliability in signal delivery DATA SHEET ARUBA 220 SERIES ACCESS POINTS • Supported data rates (Mbps): - 802.11b: 1, 2, 5.5, 11 - 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 - 802.11n: 6.5 to 450 (MCS0 to MCS23) - 802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3) • 802.11n high-throughput (HT) support: HT 20/40 • 802.11ac very high throughput (VHT) support: VHT 20/40/80 • 802.11n/ac packet aggregation: A-MPDU, A-MSDU POWER • Worst-case power consumption from the AP (excluding power drawn by an attached USB device): - In restricted mode (PoE): 13.5W - In unrestricted mode (PoE): 17W - In unrestricted mode (DC): 15.5W • Power sources sold separately • Direct DC source: 12 Vdc nominal, +/- 5% • Power over Ethernet (PoE): 48 Vdc (nominal) 802.3af or 802.3at-compliant source - Efficient mode PoE – power save with 802.3af PoE and limited functionality > USB port disabled > Second Ethernet port disabled > 2.4-GHz 802.11n radio in 1x3:1 spatial-stream mode > 5-GHz 802.11ac radio operates without restrictions* - Unrestricted functionality with 802.3at PoE+ *With ArubaOS software 6.3.0, the 5-GHz 802.11ac radio operates in 2x3:2 spatial stream mode when the AP is powered by 802.3af PoE. This restriction has been removed in 6.3.1. ANTENNAS • AP-224: Three RP-SMA connectors for external dualband antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 1.5 dB in 2.4 GHz and 3.0 dB in 5 GHz. • AP-225: Six integrated downtilt omni-directional antennas for 3x3 MIMO with maximum antenna gain of 3.5 dBi in 2.4 GHz and 4.5 dBi in 5 GHz. Built-in antennas are optimized for horizontal ceiling mounted orientation of AP-225. The downtilt angle for maximum gain is approximately 30 degrees. OTHER INTERFACES • Two 10/100/1000BASE-T Ethernet network interfaces (RJ-45) - Auto-sensing link speed and MDI/MDX - Load balancing support to achieve platform throughput greater than 1 Gbps